Hi,
maybe you could fix the configurator V2.10 earlier versions of the configurators like 2.00 were working fine. I think anybody else would have a similar problem. I think it is the resolution… (see screenshot) https://imgur.com/a/MR0BfG2
Please add a wiring diagram. I’m already confused. 1.91 works fine if RX goes to PPM pin on Taranis Q X7, M0 to S-Por. I select SBUS on Taranis and receiver, RSSI works and telemetry data is transmitted at 9600.
With firmware 2.10 I can’t use this, Taranis swears for a weak signal.
Please add a wiring diagram. I’m already confused. 1.91 works fine if RX goes to Taranis Q X7 hardware, M0 to S-Por. I select SBUS on Taranis and receiver, RSSI works and telemetry data is transmitted at 9600.
With firmware 2.10 I can’t use this, Taranis swears for a weak signal.
wow, really cool.
Maybe you can make version compatible with 32 bit stm L0 mcu ? Or maybe event something really small and unique stm32wle5 with embeded lora chip…?
Kris
I flew this system with telemetry disabled on the standard frequency grid (default) in rx silent mode . During the flight (approximately every 2-3 minutes), failsafe was turned on for a few seconds (the engine was turned off, the corresponding indication was displayed on the fpv monitor). The LRS 2.1 was connected to the fs-ia6b receiver via a transistor inverter (repeater). What can be the reason for the loss of communication at a distance of about 300-400 meters?
We use cookies to ensure that we give you the best experience on our website. If you continue to use this site we will assume that you are happy with it.Ok
Hi,
maybe you could fix the configurator V2.10 earlier versions of the configurators like 2.00 were working fine. I think anybody else would have a similar problem. I think it is the resolution… (see screenshot)
https://imgur.com/a/MR0BfG2
Yes, mee too 🙂
Hello, why is PPM not supported on the transmitter? How can I connect it directly to Radiolink AT9S hardware via the trainer port?
2.1, TX module 915, sbus – LED (M0) always on. RX module LED blinks 4 slow, 4 fast. Nothing happen im receiver tab in inav.
Please add a wiring diagram. I’m already confused. 1.91 works fine if RX goes to PPM pin on Taranis Q X7, M0 to S-Por. I select SBUS on Taranis and receiver, RSSI works and telemetry data is transmitted at 9600.
With firmware 2.10 I can’t use this, Taranis swears for a weak signal.
Please add a wiring diagram. I’m already confused. 1.91 works fine if RX goes to Taranis Q X7 hardware, M0 to S-Por. I select SBUS on Taranis and receiver, RSSI works and telemetry data is transmitted at 9600.
With firmware 2.10 I can’t use this, Taranis swears for a weak signal.
please ask your question using rcgroups topic…
Can you please explain difference between
Mavlink enc. + SPORT MASTER
and
Mavlink enc. + SPORT SLAVE?
It’s easy, if you connect directly to taranis, choose sport master, if you connect as relay to frsky rx choose slave 😉
Thank you! When I connect as relay to frsky rx – I must use resistor 1 kOm?
yes, you have to.
Can you please compile PPM version for 915 Mhz , 2.1 release? Now getting popular remote control like that: https://www.banggood.com/Payne-Open-Source-DIY-Remote-Control-Transmitter-Kit-With-PPM-Output-For-RC-Airplanes-p-1225954.html?rmmds=myorder&cur_warehouse=CN&ID=532401
please use 868MHz compilation instead…
Hey!
See my free pcb for qczek!)
https://github.com/whoim2/qczek-E32xxxTy0s-pcb
wow, really cool.
Maybe you can make version compatible with 32 bit stm L0 mcu ? Or maybe event something really small and unique stm32wle5 with embeded lora chip…?
Kris
I flew this system with telemetry disabled on the standard frequency grid (default) in rx silent mode . During the flight (approximately every 2-3 minutes), failsafe was turned on for a few seconds (the engine was turned off, the corresponding indication was displayed on the fpv monitor). The LRS 2.1 was connected to the fs-ia6b receiver via a transistor inverter (repeater). What can be the reason for the loss of communication at a distance of about 300-400 meters?
what does RX led show?
Is it stop blinking fast?